Cal Controls

Digital Process and Programmable Controllers

Features of the 9500 process controller

  • Full PID auto tuning process controller
  • 4-20mA input and output
  • Total of 3 outputs, from 4-20mA, SSR drive, relay
  • Input options:
    4-20mA
    Thermocouple
    2 or 3 wire PT100
    0-50mV, 0-5, 0-10V
  • Alarms with 5 options
  • PID heat-cool operation
  • Ramp & soak operation
  • Sleeve mounting for easy maintenance
  • IP66 protection from front panel
  • CE, UL & CSA approvals
  • 3-year warranty
  • Charting and logging software option
  • RS232/485 Modbus option


Features of the 9500P (programmer)

  • Up to 31 programs (profiles)
  • Up to 126 segments
  • Unlimited use of event outputs via the 2nd and 3rd outputs
  • Copy/paste/edit/delete functions to simplify program building
  • Call another program as a sub-program segment
  • Up to 999 program loop cycles, or continuous loop cycling
  • Hold back function to ensure the next segment is not started until the last segment reaches set-point
  • 3 power fail recovery options, (hold, continue or reset)
  • Front Panel Interrogation of the program position
  • Memory usage indication during programming
  • Front panel 'release from hold' function to run the program.

 

9500 process controller

1/16th DIN 48 x 48mm

Set-point and process value shown.

Options:

Inputs:

sensor, thermocouple, 0-5, 0-10, 4-20mA

Outputs:

(third is always relay)
Outputs 1 & 2 a combination from:
SSR driver, relay, 4-20mA, 0-5V, 0-10V

Communications:

RS232, RS485 with MODBUS RTU protocol

 

 


The 9500 is sleeve mounted allowing the fitting of comms boards for networking

 

Specification - 9500

Thermocouple types:

9 types:

     

B,E,J,K,L,N,R,S,T

Standards:

 

IPTS/68/ DIN 43710

CJC rejection:

 

20:1 (0.05†/†C) typical

External resistance:

 

100 ohms maximum

 

Resistance thermometers:

RTD/PT100:

     

2 & 3 wire

Standards:

 

DIN43760 (-200/400†C)

 

Linear process inputs:

Options:

     

0 to 50mV +/-0.1%

 

 

4-20mA +/-0.1%

 

 

0-5V +/-0.1%

 

 

0-10V +/-0.1%

 

Applicable to all inputs (SM = sensor maximum)

Calibration accuracy:

     

+/- 0.25% SM +/-1†C

Sampling frequency:

 

input 10Hz, CJC 2 sec.

Common mode rejection:

 

Negligible effect up to 140db, 240V, 50-60Hz

Series mode rejection:

 

60db, 50-60Hz

Temperature coefficient:

 

50ppm/†C SM typical

Reference conditions:

 

22†C +/- 2†C, rated voltage after 15 minutes settling time.

 

Output devices (check configuration)

SSd1 and SSd2

     

solid state relay driver: to switch a remote SSR 6VDC (nominal) 20mA non-isolated

Miniature power relay:

 

form A/SPST contacts (AgCdO)

rLY1, rLY2, rLT3:

 

2A/250VAC resistive load

Analogue output:

 

4-20mA 500 ohms max’ +/- 0.1% fs

typical

 

0-5Vdc 10mA (500 ohms min’) +/- 0.1% fs

typical

 

0-10Vdc 10mA (1K ohms min’) +/- 0.1% fs

 

General:

Displays:

     

Upper, 4 digits, high brightness green LED 10.4mm (0.4") high.

 

 

Lower, 4 digits, high brightness orange LED 9mm (0.35") high.

 

 

Digital range –199 to 9999

 

 

Hi-res mode –199 to 999.9

 

 

LED output indicators –

 

 

flashing SP1 square, green; SP2/SP3 round, red.

Keypad:

 

3 elastomeric buttons.

Power Supply:

 

100-240V AC, 50-60 Hz , (typ' 5.0 VA)

 

Environmental:

Humidity:

     

Max’ 80%

Altitude:

 

up to 2000M

Installation:

 

categories II and III

Pollution:

 

Degree II

Protection:

 

NEMA 4X, IP66

EMC emission:

 

EN50081-1 FCC rules 15 sub-part J class A 

EMC immunity:

 

EN50082-2

Ambient temperature:

 

0-50†C (32-130†F)

Mouldings:

 

flame retardent polycarbonate

Weight:

 

180g (6.4 oz)

 

Dimensions:

Front fascia:

     

51.0 x 51.0mm (2.0" x 2.0") (includes gasket)

Sleeve length:

 

106.7mm (4.2") (with gasket fitted)

Instrument body:

 

44.8 x 44.8mm (1.76" x 1.76")

Overall length:

 

116.2mm (4.57")